If you have a Frigidaire Affinity washer, it’s important to know how to clear the error codes should one appear. The codes can help you troubleshoot and fix any problems that may be occurring with your washer. The codes are displayed as blinking lights on the washer’s control panel.
The most common error code is “F-01.” This code means that the washer has lost communication with the motor. If this code appears, try unplugging the washer and plugging it back in. If the code still appears, you may need to replace the motor.
Other error codes that you may encounter include:
F-02: This code means that there is a problem with the communication between the washer’s main control board and the motor.
F-03: This code means that there is a problem with the motor.
F-04: This code means that there is a problem with the pressure switch.
F-05: This code means that there is a problem with the drain pump.
F-06: This code means that there is a problem with the water level switch.
F-07: This code means that there is a problem with the heating element.
F-08: This code means that there is a problem with the water inlet valve.
F-09: This code means that there is a problem with the timer.
If you encounter one of these error codes, you can try to clear it by unplugging the washer and plugging it back in. If the code reappears, you may need to replace the associated part.
Contents
- 1 How do you reset the code on a Frigidaire washing machine?
- 2 How do you clear the code on a washing machine?
- 3 How do you put a Frigidaire Affinity washer in diagnostic mode?
- 4 How do I troubleshoot my Frigidaire Affinity washer?
- 5 How do you reset an affinity front load washer?
- 6 How do you reset the code on a Frigidaire Affinity Dryer?
- 7 Is there a reset button on a washing machine?
How do you reset the code on a Frigidaire washing machine?
Resetting the code on a Frigidaire washing machine is a fairly simple process. You will need a flathead screwdriver to complete the process.
First, turn off the washing machine and unplug it from the wall. Then, using the screwdriver, remove the two screws that hold the control panel in place. Gently pull the panel off of the machine.
Locate the small hole on the right side of the panel. Using the screwdriver, insert it into the hole and press the button inside. This will reset the code on the machine.
Replace the control panel and screws, and plug in the machine. Turn it on and test it to make sure it is working properly.
How do you clear the code on a washing machine?
Clearing the code on a washing machine is a fairly simple process that can be completed in a few minutes. If the machine is not working correctly, or if you have forgotten the code, clearing the machine’s memory can help to resolve the problem.
To clear the code on a washing machine, locate the code reset button on the machine. This button is usually circular or square, and is located on the front or back of the machine. Press and hold the code reset button for a few seconds, then release it. The machine’s code will be cleared, and the machine will be ready to use.
How do you put a Frigidaire Affinity washer in diagnostic mode?
To put a Frigidaire Affinity washer in diagnostic mode, you will need to unplug the washer and then plug it back in. Once the washer is plugged back in, you will need to press and hold the Power Wash and Delay Start buttons at the same time. After holding the buttons down for about five seconds, the washer will start in diagnostic mode.
How do I troubleshoot my Frigidaire Affinity washer?
If your Frigidaire Affinity washer isn’t working properly, don’t worry – you can troubleshoot it! Here are a few tips to help you get your washer up and running again:
First, make sure your washer is properly plugged in and that the power is turned on.
If your washer is leaking water, make sure the hoses are properly connected and that the water valves are turned on.
If your washer isn’t draining properly, make sure the drain hose is connected and that the drain valve is open.
If your washer isn’t washing or spinning properly, make sure the water is turned on and that the washer is properly leveled.
If your washer is making strange noises, make sure nothing is blocking the washer’s fan or ventilation holes.
If you’ve tried all of these tips and your washer still isn’t working properly, you may need to call a technician.
How do you reset an affinity front load washer?
If you have an affinity front load washer, you may need to reset the machine if it becomes unresponsive or if you need to clear a malfunction. To reset the machine, you will need to power it off and unplug it from the wall. Wait for a few minutes, then plug it back in and power it on. If the machine does not reset, you may need to call a technician.
How do you reset the code on a Frigidaire Affinity Dryer?
If you have a Frigidaire Affinity dryer, you may need to reset the code at some point. This can be done by pushing the power button for two seconds, then unplugging the dryer. Plug it back in and press the power button again for two seconds. The code should now be reset.
There is no universal reset button on washing machines, although some models may have a specific button for this purpose. If your washing machine does not have a reset button, you can usually reset it by unplugging it and plugging it back in.