The F3 E2 error code on a Whirlpool washer is an indication that the washer is not draining properly. This error code can be caused by a variety of problems, including a clogged drain pump, a clogged drain hose, a defective drain motor, or a defective control board.
If the F3 E2 error code is displayed, first check to make sure that the washer is properly draining. If the washer is not draining properly, try unplugging the washer and cleaning out the drain pump and drain hose. If the washer still does not drain properly, the drain motor or control board may need to be replaced.
Contents
- 1 How do you fix an F3 error on a Whirlpool washer?
- 2 What does E2 mean on a Whirlpool washer?
- 3 What does F3 E2 mean on a Whirlpool dryer?
- 4 How do I fix E3 error on my Whirlpool washer?
- 5 How do I reset my Whirlpool washing machine?
- 6 How do I reset my Whirlpool front load washer?
- 7 How do I fix E2 error on my Whirlpool washer?
How do you fix an F3 error on a Whirlpool washer?
An F3 error on a Whirlpool washer can be caused by a number of different problems. In order to fix the F3 error, you will need to determine what is causing it.
One common cause of the F3 error is a water leak. If there is water leaking into the washer, it will cause the F3 error to occur. If you suspect that a water leak is causing the F3 error, you will need to inspect the washer for signs of water damage. If you find water damage, you will need to repair it before you can fix the F3 error.
Another common cause of the F3 error is a problem with the washer’s drainage system. If the drainage system is blocked or clogged, it will cause the F3 error to occur. If you suspect that the drainage system is causing the F3 error, you will need to inspect it for signs of blockage or clogging. If you find any signs of blockage or clogging, you will need to clear it out before you can fix the F3 error.
If you are unable to determine what is causing the F3 error, you may need to call a technician to help you troubleshoot the washer.
What does E2 mean on a Whirlpool washer?
What does E2 mean on a Whirlpool washer?
The E2 error code on a Whirlpool washer indicates that there is a problem with the water level. This could be due to a clogged water inlet, a faulty water valve, or a clogged water pump. If you experience this error code, try unplugging the washer for a few minutes and then plugging it back in. If the error code persists, you may need to call a technician to troubleshoot the problem.
What does F3 E2 mean on a Whirlpool dryer?
What does F3 E2 mean on a Whirlpool dryer?
F3 E2 is an error code that is displayed on Whirlpool dryers. This code indicates that the thermal fuse has blown. The thermal fuse is a safety device that protects the dryer from overheating. If the thermal fuse blows, it will need to be replaced.
How do I fix E3 error on my Whirlpool washer?
Whirlpool washers are one of the most popular brands on the market. They are known for their durability and quality. However, even the best machines sometimes experience problems. One common issue that people experience with Whirlpool washers is the E3 error code.
If you are experiencing this error code, there are a few things that you can do to try and fix it. The first thing you should do is check to make sure that the water is not too hot. If the water is too hot, it can cause the washer to malfunction. You can try lowering the water temperature by adjusting the hot water heater.
If the water temperature is not the issue, you may need to clean the washer’s filters. The filters can become clogged over time, which can cause the washer to malfunction. You can clean the filters by removing them and rinsing them under water.
If the filters are not the issue, you may need to replace the washer’s door switch. The door switch can malfunction over time, which can cause the washer to malfunction. You can replace the door switch by removing the front panel of the washer and locating the switch.
If none of these solutions fix the problem, you may need to call a technician to help you troubleshoot the issue.
How do I reset my Whirlpool washing machine?
If your Whirlpool washing machine is not working properly, you may need to reset it. This article will show you how to do that.
First, make sure your machine is unplugged. Then, press and hold the power button for three seconds. release the button, and then press it again. Hold the button for three seconds, and release it. Plug the machine back in, and press the power button to turn it on.
How do I reset my Whirlpool front load washer?
If your Whirlpool front load washer isn’t working properly, you may need to reset it. This article will show you how to do that.
First, make sure the washer is turned off and unplugged. Then, open the door and remove the water hose from the back of the washer. Next, unscrew the cap from the back of the washer and pull out the black reset plug. Finally, plug the water hose back in and screw the cap back on. Now, turn the washer on and wait for it to fill up with water. Once it does, the reset process is complete.
How do I fix E2 error on my Whirlpool washer?
If you’re experiencing an E2 error on your Whirlpool washer, don’t worry – you’re not alone. This error is often caused by a problem with the machine’s water level sensor, and it can usually be fixed with a little bit of troubleshooting.
The first thing you’ll want to do is check the water level sensor for any signs of damage or corrosion. If it’s damaged, you’ll need to replace it. If it’s corroded, you can try cleaning it with a little bit of vinegar.
If the water level sensor looks good, the next thing you’ll want to do is check the wiring. Make sure the wiring is securely connected and that there are no shorts or breaks in the wire.
If everything looks good, the next step is to recalibrate the water level sensor. To do this, you’ll need to access the washer’s diagnostic mode. To do this, press and hold the “Cancel” and “Prewash” buttons on the washer for three seconds. Then, press the “Start/Pause” button to enter the diagnostic mode.
Once you’re in the diagnostic mode, use the “Up” and “Down” arrows to select “Water Level Sensor Calibration.” Press the “Start/Pause” button to begin the calibration process.
The calibration process will take about two minutes to complete. When it’s finished, the washer will automatically exit the diagnostic mode. If the calibration was successful, the E2 error should be gone.
If the calibration process fails, the washer will display an “F5” error code. In this case, you’ll need to replace the water level sensor.